麻豆成人久久精品二区三区-日韩二级片在线免费观看-老熟女老女人国产老太中国-国产成人av麻豆精品

服務熱線: 400-117-8816
           13406879330

扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家

當前位置:首頁>新聞中心扭剪型高強螺栓安裝規定

扭剪型高強螺栓安裝規定

來源:http://brianstaruk.com日期:2022-07-12 發布人:admin

1 安裝時高強螺栓應自由穿入孔內,不得強行敲打。扭剪型高強螺栓的墊圈安在螺母一側,墊圈孔有倒角的一側應和螺母接觸,不得裝反(大六角頭、高強螺栓的墊圈應安裝在螺栓頭一側和螺母一側,墊圈孔有倒角一側應和螺栓頭接觸,不得裝反)。

1. During installation, high-strength bolts should be freely penetrated into the hole, and forced tapping is not allowed. The washer of torsion shear high-strength bolt shall be installed on the side of the nut, and the side with chamfer in the washer hole shall be in contact with the nut and shall not be installed upside down (the washer of large hexagon head and high-strength bolt shall be installed on the side of the bolt head and the nut, and the side with chamfer in the washer hole shall be in contact with the bolt head and shall not be installed upside down).
2 螺栓不能自由穿入時,不得用氣割擴孔,要用絞刀絞孔,修孔時需使板層緊貼,以防鐵屑進入板縫,絞孔后要用砂輪機孔邊毛刺,并鐵屑。
2. When bolts cannot be penetrated freely, gas cutting shall not be used to ream holes, and reaming with a reamer shall be used. When repairing holes, the plate layer shall be close to prevent iron filings from entering the plate seam. After reaming holes, use a grinder to remove burrs at the hole edge and remove iron filings.
3 螺栓穿入方向宜一致,穿入高強螺栓用扳手緊固后,再卸下臨時螺栓,以高強螺栓替換。不得在雨天安裝高強螺栓,且摩擦面應處于干燥狀態。
3 bolts should be threaded in the same direction. After threading high-strength bolts and tightening them with a wrench, remove the temporary bolts and replace them with high-strength bolts. High strength bolts shall not be installed in rainy days, and the friction surface shall be dry.
4.高強螺栓的緊固:必須分兩次進行,次為初擰。初擰緊固到螺栓標準軸力(即設計預拉力)的60%~80%,初擰的扭矩值不得小于終擰扭矩值的30%。第二次緊固為終擰,終擰時扭剪型高強螺栓應將梅花卡頭擰掉。為使螺栓群中所有螺栓均勻受力,初擰、終擰都應按一定順序進行。一般接頭:應從螺栓群中間順序向外側進行緊固。從接頭剛度大的地方向不受約束的自由端進行。從螺栓群向四周擴散的方式進行。
4. Fastening of high-strength bolts: it must be carried out in two times, and the first time is initial tightening. The initial tightening shall be tightened to 60% - 80% of the standard axial force (i.e. design pretension) of the bolt, and the torque value of the initial tightening shall not be less than 30% of the torque value of the final tightening. The second tightening is the final tightening. During the final tightening, the Torx clamp shall be screwed off. In order to make all bolts in the bolt group bear the force evenly, the initial tightening and final tightening should be carried out in a certain order. General joints: tighten from the middle of the bolt group to the outside. From the place with large joint stiffness to the unrestrained free end. From the center of the bolt group to the surrounding areas.
以上就是為大家介紹的有關扭剪扳手的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務.http://brianstaruk.com
The above is a detailed introduction to the torsion shear wrench, which I hope will be helpful to you If you have any questions, please contact us We will provide you with professional service http://brianstaruk.com

国产精品一区二区日韩新区| 国产一区二区三区香蕉av| 午夜激情视频一区二区| 日本女人亚洲国产性高潮视频| 亚洲精品福利视频在线观看| 97人摸人人澡人人人超碰| 欧美美女视频在线免费看| 久热99中文字幕视频在线 | 亚洲精选91福利在线观看| 精品少妇人妻av一区二区蜜桃| 中文字幕中文字幕一区二区| 四季精品人妻av一区二区三区 | 日本免费熟女一区二区三区 | 五月婷婷缴情七月丁香| 国产亚洲精品久久99| 免费久久一级欧美特大黄孕妇| 亚洲成人黄色一级大片| 亚洲精品国男人在线视频| 91免费一区二区三区| 国产精品一区二区传媒蜜臀| 日本免费熟女一区二区三区| 欧美特色特黄一级大黄片| 国产午夜在线精品视频| 美女激情免费在线观看| 又色又爽又无遮挡的视频| 成人亚洲国产精品一区不卡| 亚洲一区二区三区四区| 亚洲精品成人福利在线| 懂色一区二区三区四区| 在线免费国产一区二区三区| 国产精品亚洲综合天堂夜夜| 午夜亚洲精品理论片在线观看| 综合久综合久综合久久| 在线免费国产一区二区| 激情综合五月开心久久| 亚洲欧美日本国产有色| 日本高清视频在线播放| 熟女白浆精品一区二区| 丰满人妻熟妇乱又伦精另类视频| 日韩一区二区三区18| 成年女人午夜在线视频|